EP brand name substitution gearbox for woods rotary gearbox

NEW forty HP GEARBOX Clean Enter 1 three/eight twelve spline output Interchangable with market place well-liked dimension i.e.: OMNI GRIZZLEY CHEETAH HOWSE KING KUTTER BUSH HOG HICO SILVER EDGE A lot of Far more

Attributes
(one) manufacturer new 45 horse electricity shearpin gearbox. This gearbox matches numerous distinct helps make of 4′,5′ and some 6′ rotary cutters. I offer a lot of these containers each and every year for a number of various apps and have ALL Substitution Elements for this box, but hopefully you will not have to worry about that.
Below are the specs on the box:
*forty five horse electrical power gearbox
*Standard one-three/eight” sleek enter shaft(the place the pto shaft hooks on). The pto shaft is held on by a 1/2 shearbolt.
*duration of the enter shaft out of the gearbox is 3″ prolonged
*bolt hole sample for mounting is on the corners, 4-three/4 heart of gap to heart of gap. It will take a 5/eight” bolt.
*12 splined output shaft(where the blade carrier hooks up on the bottom)
*one-nine/16 outside measurement over the output shaft splines- from the foundation of the output cap to the stop of the splines is 2-3/four” prolonged- general size of the output shaft is 4-one/two” prolonged.
*normally takes a one” threaded castle nut and a carter crucial on the base of the output shaft to protected blade pan(NUT is included – – BLADE PAN IS NOT!!)
*all round peak of the box from the prime of the mower deck to the prime of the box is nine-one/2″
This is a relatively hefty item (forty seven lbs.) so freight is not low-cost, but we do not make anything off of freight, whatsoever ups expenses us we demand you.
40 HP
one:one:forty seven Ratio
one-3/8″ Clean Input Shaft with Shear Pin Hole
1-one/two” 12-Spline Ouput Shaft
Bolt Sample: six-one/2″ (four) 5/8″ Holes, 5″ Middle Hole Necessary for Shaft Assembly
The Enter and Output Shafts Are not able to be Bought Serparately.
They are Offered as a package.
The kit contains the following elements: input shaft, input equipment, output shaft, output equipment.
The Shaft Package Cannot Be Separated.

EP brand replacement gearbox for woods rotary gearbox

Rotary Cutter Gearbox Troubleshooting Guide
Is your mower leaking, creaking or normally executing improperly? You have occur to the proper place.

Read below for the most widespread problems with rotary cutter gearboxes and their solutions (from rapid and dirty, to professional).

Leaking Base Seal:
If you have wrapped some baling or fencing wire around your output shaft and blown the seal, the professional factor to do is to change the seal.
If your output seal is intact, and you are able to get ID, OD and thickness measurements (in millimeters), most bearing houses can get you up a generic double-lip seal that will get you back again up-and-running. If not, give us a get in touch with and we can support you sort out what you need to have.
A dental pick is the least difficult way to take away the previous seal before pressing in the new one.
If you are lucky adequate to have a slow-leak, the rapid and filthy approach is to operate automotive-variety grease in the gearbox until the new seal arrives in. Be positive to check out and add grease far more regularly than you would with oil, as this is NOT a specialist repair.

Damaged Output Shaft:
Uh oh. You strike anything that did not move. The great news is that the output shaft on most gearboxes is pretty simple to replace. The bad news is… it truly is rarely an isolated failure.
The first factor to do is to consider apart your gearbox and assess the entire extent of the damage. If it is actually just the output shaft, you must be in a position to alter it out, no difficulty. The output shafts begin at about $70 and go up in cost dependent on the dimensions of the gearbox.
However, in most instances, the bearings ($20/ea), seals ($ten/ea) and gear-established ($70) will also normally consider a beating. If you’re unlucky, the output cap ($80) will also suffer some injury.
In this case, it is generally less expensive to substitute the gearbox. Examine the price of components to the value of an total, new, warrantied gearbox. At times, even pros have to know when to contact it a working day.

I Want to Adjust my Enter Shaft:
If you are drained of altering shear pins or searching again and looking at that your mower hasn’t been chopping, you may possibly want to install a slip-clutch pto shaft (Of course, we market individuals also).
This typically calls for installing a 540-fashion, six-spline input shaft ($85) on your mower’s gearbox.
Fortunate for you, we did a compose-up on our website. It truly is referred to as “How to change the input shaft on your rotary cutter gearbox”.

My Gearbox is Groaning/Creaking:
“Groaning”, “creaking”, or “popping” all sound variety-of equivalent above-the-phone. The greatest point to do is to disassemble your gearbox and just take a seem at the gears and bearings. The concern will normally present itself in the way of damaged/lacking gear enamel, toasted gears (like that photo on our residence page), or blown bearings.
If every little thing looks typical, consider altering the equipment-mesh. This is completed with the mylar “gaskets” that sit between the major gearbox case and the input/output caps. Try including or eliminating some of these spacers right up until your gears have roughly 1/8″-one/four” of free play. Pros can get replacements ($1-2) in varying thicknesses, but we advocate the swift and filthy strategy of chopping your very own out of a sheet of mylar.
Never fail to remember to re-seal the gearbox with RTV after you have identified the proper mix. Even however they are called “gaskets”, they will not likely seal your gearbox on their personal.

Learn more regarding Gearbox geared motors For Horticulture Drive Systems at http://agricultural-gearbox.xyz/agricultural-gearbox/gearbox-reducer-for-climate-screens-drive.html.