0086-571-88220973 / 88220971 [email protected]
0 Items

L Series PTO Shaft Lemon Tube L1 L2 L3 L4 L5 L6 L32

Regardless of what job you’ll be using a PTO shaft to complete, it’s important that you have the right size. The manufacturer should provide length recommendations to help you get an idea. When measuring a PTO shaft, use a tape measure and measure from the outside of each yoke to obtain the closed length. The series size should correspond with the amount of horsepower your tractor has. There are two different speeds used most commonly with tractor PTO shafts, the 540 (type 1) and 1000 (type 3) RPM.

Category:
Get a Quote

L Series PTO Shaft Lemon Tube L1 L2 L3 L4 L5 L6 L32

 

L Series PTO Shaft

Series

540 tr./min 1000 tr./min MP(NM)
Kw Pk Nm Kw Pk Nm
L1 12 16 210 18 25 172 320
L2 15 21 270 23 31 220 450
L3 22 30 390 35 47 330 640
L4 26 35 460 40 55 380 780
L5 35 47 970 54 74 520 1050
L6 47 64 830 74 100 710 1450
L32 39 53 695 61 83 580 1200

Size Importance

Regardless of what job you’ll be using a PTO shaft to complete, it’s important that you have the right size. The manufacturer should provide length recommendations to help you get an idea. When measuring a PTO shaft, use a tape measure and measure from the outside of each yoke to obtain the closed length. The series size should correspond with the amount of horsepower your tractor has. There are two different speeds used most commonly with tractor PTO shafts, the 540 (type 1) and 1000 (type 3) RPM.

Part of PTO Shaft

Internal Yoke- There are two, located at both ends of the PTO shaft -tractor and implement. This is welded to the drive end.
Universal Joint- There are two, located at both ends of the PTO shaft.
External Yoke- There are two, located at both ends of the PTO shaft. It has a “Y” shape to connect to the U-joint and a female hole.
Safety Chains- The chains are used to secure the PTO shaft onto the equipment and onto the tractor.
Safety Shield- These cones are found on both ends.

L Series PTO Shaft

 

Series Cross Joint simple Splined yoke Tube yoke Tube
Outer Inner Outer Inner Outer Inner
1 2 3 4 5 6 7 8
L1 1.01
(22*54)
1.0505B+1.01+1.06L 1.0505B+1.01+1.07L 1.0505B 1.06L 1.07L 1.03L 1.04L
L2 2.01
(23.8*61.3)
2.0505B+2.01+2.06L 2.0505B+2.01+2.07L 2.0505B 2.06L 2.07L 4.03L 4.04L
L3 3.01
(27*74.6)
3.0505B+3.01+3.06L 3.0505B+3.01+3.07L 3.0505B 3.06L 3.07L
L4 4.01
(27*74.6)
4.0505B+4.01+4.06L 4.0505B+4.01+4.07L 4.0505B 4.06L 4.07L
L5 5.01
(30.2*80)
5.0505B+5.01+5.06L 5.0505B+5.01+5.07L 5.0505B 5.06L 5.07L 6.03L 6.04L
L6 6.01
(30.2*92)
6.0505B+6.01+6.06L 6.0505B+6.01+6.07L 6.0505B 6.06L 6.07L
L32 32.01
(32*76)
32.0505B+32.01+32.06L 32.0505B+32.01+32.07L 32.0505B 32.06L 32.07L

Lemon Tube

 

L Series PTO Shaft lemon tube

Without the PTO, a tractor cannot drive to complete its most basic of functions. Comprehending the different types of PTO shafts, parts, and their respective uses will allow for better practice with farm machinery. After all, you want an investment in the expensive and necessary equipment to last as long as possible.

How Does PTO Shaft Work?

L Series PTO Shaft
The Power Take-Off shaft transfers power from your tractor to the equipment of your choice. The PTO driveline is where everything that needs power on a tractor derives its power from. PTO drivelines are often overlooked during routine maintenance checks but should not be ignored as they are crucial in operating farm equipment.

Wear and Tear

When you’re operating agricultural equipment, there’s inevitably going to be wear and tear. Areas to watch out for this especially are with the yoke ears or sides that can be damaged from working excessively at angles. If the angle exceeds forty-five degrees, the PTO should be disengaged.

Telescoping tubing and sections can also experience excessive wear if lubrication is lacking where the tubes overlap. Insufficient lubrication can also cause undue wear on shield bearings. Without proper lubrication, the friction between these bearings is too great. They should be lubricated every eight hours.

Damaged or Broken Parts

It’s important to pay attention when things start to run less smoothly, or you find your attention on an area of the machinery that ordinarily runs smoothly. Damage to parts can happen anywhere from telescope tubes to cross-bearing arms, or joints to yokes. Be aware of the shock load on your equipment and make sure that you are using the right type of PTO for the job you are attempting to accomplish. Heavy-duty equipment can take a lot of stress, but it’s important to stop if something isn’t right before damaging beyond a simple fix.

industries we service

We promise will offer the best price by the high quality in china! We also accept special order about the products. If you are interested in our products. Please do not hesitate to let us know.We are pleased to give you the detailed information.We promise that our products would be safety and were in high quality and reasonable price. If you are interested in our products, please contact us asap.We are sincerely looking for your cooperation.

Most of our products are exported to Europe or Americas, both standard and nonstandard products available. We can produce as per your drawing or sample. Material can be standard or as per your special request. If you choose us, you choose reliable.

hzpt oem odm banner

pruduct quality report

Surface Treatment

Annealing, natural canonization, heat treatment, polishing, nickel plating, chrome plating, zinc plating,yellow passivization, gold passivization, satin, Black surface painted etc.product materials available

Processing Method

CNC machining, punch,turning, milling, drilling, grinding, broaching, welding and assembly

product finishing

 

product packages

FAQ

Q: Are you trading company or manufacturer ?
A: Our group consists in 3 factories and 2 abroad sales corporations.

Q: Do you provide samples ? is it free or extra ?
A: Yes, we could offer the sample for free charge but do not pay the cost of freight.

Q: How long is your delivery time ? What is your terms of payment ?
A: Generally it is 40-45 days. The time may vary depending on the product and the level of customization. For standard products, the payment is: 30% T/T in advance ,balance before shipment.

Q: What is the exact MOQ or price for your product ?
A: As an OEM company, we can provide and adapt our products to a wide range of needs.Thus, MOQ and price may greatly vary with size, material and further specifications; For instance, costly products or standard products will usually have a lower MOQ. Please contact us with all relevant details to get the most accurate quotation.

Pin It on Pinterest