0086-571-88220973 / 88220971 hzpt@hzpt.com
0 Items

SF QD Type Bushings

Category:
Get a Quote

SF QD Type Bushings

Type SF QD bushings are designed for use on sprockets and pulleys with tapered ends. The design allows for interchangeable shafts of various sizes. They are also easy to install. Bushings come with lock washers and bolts, SF 2-1/4" bushings can be used on any "SF" sprocket hub. While you can use lubricant during installation, it is not necessary to use it on the bolts.
SF QD-style bushings feature a tapered design for excellent retention. They are available in metric and common hole sizes and include set screws or counterweights for mounting. The dual adjustment tensioner allows full idler rotation due to the base's long slot. A tapered fit holds the bushing in place. When installing dual adjustable tensioners, follow the drive type's installation guide.
When installing the MPB bushing, place the threaded holes on the pulley as far as possible from the bushing's kerf. To ensure proper wedging action, be sure to use loose-threaded cap screws with lock washers on the threads. Once installed, you can remove the mating hub by loosening the cap screw and turning it counterclockwise.

Dimensions of SF QD Type Bushings

QD Bushings

  • Bushing Type: SF
  • Bore Size: 1-1/4"、1-3/8"、1/2"、11/16"、15/16"、25mm、30mm、32mm、35mm、40mm、42mm、45mm、48mm、5/8"、50mm、55mm、60mm、65mm、7/8"、70mm、
  • Dimension (A): 0.563"
  • Dimension (B): 3.125"
  • Dimension (D): 4.625"
  • Dimension (E): 1.500"
  • Dimension (F): 1.250"
  • Dimension (G): 0.125"
  • Dimension (L): 2.000"
  • Bolt Circle: 3.875"
  • Set Screw Size: 5/16 - 18
  • Wrench Torque: 360 LBS
  • Weight: 3.00 LBS

Standard Mounting

1. Make sure the cone on the bushing and the inside of the driven product is clean and free of oil or any anti-seize lubricant.
2. Slide QD bushing on a shaft, flange end first, then assemble key.
3. Place the QD bushing on the shaft. Use only a standard Allen key to tighten the set screw on the key (hand-tight). Don't push too hard.
4. Slide the large end of the sprocket or other part taper hole into place over the cone, aligning the drilled bolt holes on the sprocket or other part with the taper holes in the bushing flange. Then assemble the pull-up bolt and lock washer.
5. Tighten the pull-up bolts alternately and evenly to the tightening levels shown in the torque table below. Do not use extensions on wrench handles. There should now be a gap between the face of the sprocket or other part hub and the flange of the QD bushing to ensure a satisfactory tapered grip and press fit. NOTE: This gap must not be closed.

Dismounting

A bushing is a component that provides a bearing surface for the forces acting axially on the shaft. A typical example of a thrust bearing is a propeller shaft. The bushing can be a separate part of an integral part of the machine. Typically, bushings are replaceable, while integral bearings are permanent and should not be replaced unless worn or damaged. Bushings are most commonly used in machinery, where they allow relative movement between components.

Click and check out more products you're looking for.

Q1. Are you a factory?
A. Yes. We are a factory with more than 15 years of manufacturing experience.

Q2. Is OEM and ODM service available?

A. Of course. We have many years of experience in OEM& ODM service.

Q3. I am buying from another supplier, but need better service. Would you match or beat the price I am paying?
A. We always feel we provide the best service and competitive prices. We would be happy to personalize a competitive quote for you; email us.

Additional information

Edited

CX

industries we service

We promise will offer the best price by the high quality in china! We also accept special order about the products. If you are interested in our products. Please do not hesitate to let us know.We are pleased to give you the detailed information.We promise that our products would be safety and were in high quality and reasonable price. If you are interested in our products, please contact us asap.We are sincerely looking for your cooperation.

Most of our products are exported to Europe or Americas, both standard and nonstandard products available. We can produce as per your drawing or sample. Material can be standard or as per your special request. If you choose us, you choose reliable.

hzpt oem odm banner

pruduct quality report

Surface Treatment

Annealing, natural canonization, heat treatment, polishing, nickel plating, chrome plating, zinc plating,yellow passivization, gold passivization, satin, Black surface painted etc.product materials available

Processing Method

CNC machining, punch,turning, milling, drilling, grinding, broaching, welding and assembly

product finishing

 

product packages