1210 Taper Lock Bushings

Category:
Get a Quote

1210 Taper Lock Bushing
One thousand two hundred ten bushings belong to the "taper lock" category and can be found in a range of roller chain sprockets and pulleys. Available in bores ranging from 1/2" to 1-1/4" (imperial) and 11mm to 32mm (metric), these bushings are the third-largest tapered bushing type. Tapered lock bushings are used in applications where narrow lengths of through-holes are required, or shaft mounting must be close to the bearing. The universal design keeps center loads small, preventing problems with high cantilever loads. The 1210 bushings are separated by a flange, while the tapered taper provides accurate clamping on the shaft, equivalent to a "shrink fit."
1210 Tapered Lock Bushings are used in a wide variety of applications for several different reasons. We offer our customers high-quality inch and metric size tapered locking bushings at the best prices in the industry without sacrificing quality. These bushings will be directly interchangeable with other manufactured bushings, so you don't have to worry about compatibility. Each 1210 Tapered Locking Bushing product page includes instructions on how to install and remove the bushing and size and wrench torque information to ensure you have all the information you need to install or remove the bushing properly. Additionally, we can supply bushings in stainless steel and unique bores upon request! For more information or to get a quote for the 1210 Tapered Locking Bushing, please get in touch with us and we will be happy to assist you.

Dimensions of the 1210 Taper Lock Bushings

product data

  • Bushing Number: 1210
  • Bore: 1"、1/2"、10mm、11/16"、11mm、12mm、13/16"、14mm.....
  • Dimension (A): 1-7/8"
  • Dimension (B): 1"
  • Dimension (D): 1-3/4"
  • Number Of Set Screws: 2
  • Threads: 3/8"
  • Length: 5/8"
  • Wrench Torque: 175 LBS
  • Weight: 0.5 LBS

Installation

1. Clean all oil, dirt, and paint from the shaft, bushing holes, bushing exterior, and bores of components (sprockets, pulleys, etc.).
2. Insert the bushing into the assembly. Match hole patterns, not threaded holes (each hole is threaded on one side only).
3. Thread the set screw or cap screw into the half-threaded hole shown below. Install the assembly on the shaft.
4. Alternately set the torque setting or cap screw* to the recommended torque setting in the table below.
5. Fill all unoccupied holes with grease.

diagram

Removal

1. Remove any retaining or cap screws.
2. Insert the set screw or cap screw into the above hole.
3. To reinstall, complete all five (5) installation instructions.

diagram

What are the symptoms of a damaged bushing?

In terms of insulation, the W-sleeve consists of two layers. The outermost layer consists of porcelain. The innermost insulation system consists of concentric capacitors. The outermost layer consists of several layers and is used for electrical testing. Although this is a solid insulation system, it requires extensive metal fittings and flexible seals. It is recommended for voltages of 26 kV or lower.
Changes in PF indicate that moisture has penetrated and degraded the casing. Also, if the PF value doubles, the bushing needs to be replaced. Another degradation indicator is the change in capacitance, measured in milligrams (pF). A 10% increase from its nameplate value indicates that the bushing needs to be replaced. So, what are the symptoms of a damaged W bushing?
Hot Loop Test: This test is performed on the bushing to evaluate its ability to conduct current. Using a conductive ring around the porcelain, the test can determine if the dielectric loss has occurred through the sleeve. It can also detect cracked porcelain, deteriorated cement joints, gasket leaks, and faults within the condenser layers. Additionally, this test checks the oil level in the oil-filled bushing.

Click and check out more products you're looking for.

Q1. Are you a factory?
A. Yes. We are a factory with more than 15 years of manufacturing experience.

Q2. Is OEM and ODM service available?

A. Of course. We have many years of experience in OEM& ODM service.

Q3. I am buying from another supplier, but need better service. Would you match or beat the price I am paying?
A. We always feel we provide the best service and competitive prices. We would be happy to personalize a competitive quote for you, email us.

Additional information

Edited

CX

Category:
hzpt oem odm banner

We promise will offer the best price by the high quality in china! We also accept special order about the products. If you are interested in our products. Please do not hesitate to let us know.We are pleased to give you the detailed information.We promise that our products would be safety and were in high quality and reasonable price. If you are interested in our products, please contact us asap.We are sincerely looking for your cooperation.

Most of our products are exported to Europe or Americas, both standard and nonstandard products available. We can produce as per your drawing or sample. Material can be standard or as per your special request. If you choose us, you choose reliable.

Industries We Service

industries we service