BM3 Hydraulic Motor for Feed Mixer

Feature of BM3 Hydraulic Motor

• Adopt the design of embedded stator and rotor, with higher oil distribution accuracy and mechanical efficiency.
• A double rolling bearing design can withstand higher lateral force.
• The imported shaft seal is designed to withstand high back pressure and can be used in series and parallel.
• Convenient forward and reverse conversion, stable speed.
• Various installation and connection forms of flanges, output shafts, oil ports, etc.

1. Intermittent refers to the maximum inlet pressure, and continuous working pressure refers to the working differential pressure.
2. The motor shall not work at the highest pressure and speed at the same time.
3. The running time of the motor shall not exceed 10% per minute under intermittent working conditions.
4.  The maximum working temperature is 80 ℃.
5. The maximum allowable back pressure of the motor is 10MPa, but it is recommended that the back pressure should not exceed 5MPa. If it exceeds 5MPa, it should be connected to the external drain pipe.
6.  Before the motor works at full load, it is recommended to run in under 40% of the maximum working pressure for 1 hour
7. It is recommended to use anti-wear hydraulic oil with a viscosity of 37-73cSt and cleanliness of ISO18/13.

1.Race/Bearing  2.Washer/Thrust  3.Kit/Seal  4.Key/Woodruff 1/4x1   5.12-PT CS 5/16X1-3/4 NF  6.12-PT CS 5/16X7/8 NF

Application of Hydraulic Motor in Feed Mixer

The use of hydrostatic drives for auxiliary and propulsion functions is illustrated by an example of a self-propelled feed mixer. The chopper at the front of the conveying channel is driven by a compact HMF 55-02 fixed displacement motor. As required, it is supplied by HPV 105-02 variable displacement pump. It can also be used to drive the conveyor belt, which can be located in the channel or arranged in other configurations.
The driver has a perfect overview of the cutting process and can move the machine sensitively and accurately. The reason is hydraulic rear-wheel drive. This includes two variable motors, which are directly connected to the wheels via gears.
The hydraulic motor can switch between two displacements, so it takes over the function of the mechanical gearbox. The machine can move sensitively through the second HPV 105-02.
The speed change of the device is controlled by an electrical control signal, which is determined by the operator's accelerator pedal. Due to the PTO function of the 02 series unit, the pump of the drive and auxiliary circuits can be directly connected behind the other. The pump separator gearbox is not required.

We can also supply all the parts for the feed mixer.

How to maintain the cycloidal hydraulic motor

Most people have never heard of cycloidal hydraulic motor, but it has been applied since the last century. It is a slow rotating rotor driven by a spline shaft, which has brought good news to industries such as industry and manufacturing. It has also been used in a high range and frequency. After using the cycloidal hydraulic motor for a long time, it must be maintained, Here is a simple explanation for you.

When operating the cycloidal hydraulic motor, we should regularly check and replace the oil, so as to avoid impurities in the oil affecting the normal use of the cycloidal hydraulic motor. The inlet oil filter of the cycloidal hydraulic motor oil pump shall be flushed regularly to repair the leakage in the system. Regularly check whether the hydraulic oil is acidified and polluted by other pollutants. We can tell whether the oil deteriorates from the smell of the hydraulic oil. If any, we should replace it in time to prevent affecting the normal use of the cycloidal hydraulic motor. The motor rotor of the hydraulic motor rotor. Slight grinding or damage Regrind and replace; If the damage is serious, it can be repaired by electroplating the inner hole with a brush, or accurately measured by cutting the wire, and then removed and replaced with new parts after heat treatment. Shaft end oil leakage: because the oil seal and the output shaft are in constant friction during daily use of the motor, it will inevitably lead to wear of the contact surface between the oil seal and the shaft. If it exceeds a certain limit, the oil seal will lose its sealing effect, leading to oil leakage. Treatment: replace the oil seal. If the output shaft is seriously worn, replace the output shaft at the same time. In our daily work, we should ensure that no particles enter the vent tank of the oil tank, the plug seat of the oil filter, and other openings in the oil tank to prevent oil contamination.

The above is the content on how to maintain and repair the cycloidal hydraulic motor. I believe you will have a general understanding of how to maintain and repair the cycloidal hydraulic motor after reading it, and you should pay attention to safety when using the cycloidal hydraulic motor, not use it randomly, and use it safely and carefully. I hope that the above maintenance and repair of the cycloidal hydraulic motor can help you, and you can check it when necessary.